hu:arduino:micro_sd_card

Differences

This shows you the differences between two versions of the page.

hu:arduino:micro_sd_card [2017/09/21 13:18]
hu:arduino:micro_sd_card [2022/04/21 15:02] ()
 1:  1:
 +{{ :wiki:arduino:micro_sd_card.png?200|Micro SD kártyamodul}}
 +====== Micro SD kártyamodul ======
  
 +A modul (Micro SD Card Adapter) egy Micro SD kártyaolvasó modul. A modul az Arduino-val való kommunikációjához [[hu:comm:bus_spi#spi|SPI]] buszt használ. 
 +A modul csatlakoztatását követően a modulba behelyezett kártya fájlrendszere az Arduino felől elérhető, az írható és/vagy olvasható.
 +Jellemző felhasználása: mérésadatok loggolása.
 +
 +Az Arduino SPI összefoglalása itt található: [[hu:arduino:start#arduino_spi|Arduino SPI]]. \\  
 +Az Aduino-s SPI megoldások összefoglalása itt található: [[hu:arduino:comm_example#arduino_spi_com|Arduino SPI kommunikáció]].
 +
 +A modulban felhasználásra szánt SD kártyát előzetesen formattálni kell. Az Arduino megbirkózik a FAT16 és FAT32-es formátumokkal is, mindenesetre a FAT16 a támogatott. Az SD kártyán használt fájlnevek esetében a szigorúbb, 8.3 forma érvényes, azaz 8 karakter fájlnév és 3 karakter kiterjesztés. Fontos, hogy a file.write() parancs mindaddig nem ír az SD kártyára, míg az előző írásműveletet vagy a close() vagy a flush() paranccsal le nem zárjuk azt. A legegyszerűbb rögtön az írás után lezárni a nyitott fájlt:
 +
 +<hidden A szoftver megjelenítése>
 +<code c>
 +  File dataFile = SD.open(filename, FILE_WRITE);
 +    if (dataFile) {
 +    dataFile.println(dataString);
 +    dataFile.close();
 +    // print to the serial port too:
 +    Serial.println(dataString);
 +  }
 +</code>
 +</hidden>
 +
 +===== Micro SD kártyamodul portok =====
 +Több típusú kártyamodul is létezik a piacon, itt most csak ezt az egyet ismertetem. Ha szükséges, kibővítem a dokumentációt.
 +
 +===== Micro SD kártyamodul bekötése =====
 +A kártyamodul portjait az alábbiak szerint érdemes az Aduino UNO-val vagy Mega-val összekötni:
 +
 +^Micro SD^Arduino Uno^Arduino Mega|
 +|CS|pin 4|pin 53|
 +|SCK|pin 13|pin 52|
 +|MOSI|pin 11|pin 51|
 +|MISO|pin 12|pin 50|
 +|VCC|5V|5V|
 +|GND|GND|GND|
 +
 +{{:wiki:arduino:micro_sd_card_wiring.png?300|Micro SD kártyamodul bekötése az UNO-n}}
 +
 +A Micro SD kártyamodul leírása a Arduino oldalon itt található:
 +
 +https://www.arduino.cc/en/Reference/SD
 +
 +===== Micro SD kártyamodul szoftver / könyvtár =====
 +
 +A Micro SD kártyamodul könyvtára innen tölthető le: https://github.com/greiman/SdFat
 +
 +Ugyaninnen a példaprogramok széles választéka is letölthető: https://github.com/greiman/SdFat/tree/master/examples
 +
 +<hidden "SD card datalogger" szoftver megjelenítése>
 +<code c>
 +/*
 +  SD card datalogger
 +
 +  This example shows how to log data from three analog sensors
 +  to an SD card using the SD library.
 +
 +  The circuit:
 +   analog sensors on analog ins 0, 1, and 2
 +   SD card attached to SPI bus as follows:
 + ** MOSI - pin 11
 + ** MISO - pin 12
 + ** CLK - pin 13
 + ** CS - pin 4 (for MKRZero SD: SDCARD_SS_PIN)
 +
 +  created  24 Nov 2010
 +  modified 9 Apr 2012
 +  by Tom Igoe
 +
 +  This example code is in the public domain.
 +
 +*/
 +
 +#include <SPI.h>
 +#include <SD.h>
 +
 +const int chipSelect = 4;
 +
 +void setup() {
 +  // Open serial communications and wait for port to open:
 +  Serial.begin(9600);
 +  while (!Serial) {
 +    ; // wait for serial port to connect. Needed for native USB port only
 +  }
 +
 +
 +  Serial.print("Initializing SD card...");
 +
 +  // see if the card is present and can be initialized:
 +  if (!SD.begin(chipSelect)) {
 +    Serial.println("Card failed, or not present");
 +    // don't do anything more:
 +    while (1);
 +  }
 +  Serial.println("card initialized.");
 +}
 +
 +void loop() {
 +  // make a string for assembling the data to log:
 +  String dataString = "";
 +
 +  // read three sensors and append to the string:
 +  for (int analogPin = 0; analogPin < 3; analogPin++) {
 +    int sensor = analogRead(analogPin);
 +    dataString += String(sensor);
 +    if (analogPin < 2) {
 +      dataString += ",";
 +    }
 +  }
 +
 +  // open the file. note that only one file can be open at a time,
 +  // so you have to close this one before opening another.
 +  File dataFile = SD.open("datalog.txt", FILE_WRITE);
 +
 +  // if the file is available, write to it:
 +  if (dataFile) {
 +    dataFile.println(dataString);
 +    dataFile.close();
 +    // print to the serial port too:
 +    Serial.println(dataString);
 +  }
 +  // if the file isn't open, pop up an error:
 +  else {
 +    Serial.println("error opening datalog.txt");
 +  }
 +}
 +</code>
 +</hidden>
 +
 +
 +===== Források =====
 +https://www.arduino.cc/en/Reference/SDCardNotes \\
 +https://www.mschoeffler.de/2017/02/22/how-to-use-the-microsd-card-adapter-with-the-arduino-uno/ \\ 
 +https://www.arduino.cc/en/Reference/SD